forked from g4klx/MMDVM
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Config.h
136 lines (104 loc) · 4.2 KB
/
Config.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
/*
* Copyright (C) 2015,2016,2017,2018,2020 by Jonathan Naylor G4KLX
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#if !defined(CONFIG_H)
#define CONFIG_H
// Allow for the selection of which modes to compile into the firmware. This is particularly useful for processors
// which have limited code space and processing power like the STM32F103, which is found on older/cheaper boards.
// Enable D-Star support.
#define MODE_DSTAR
// Enable DMR support.
#define MODE_DMR
// Enable System Fusion support.
#define MODE_YSF
// Enable P25 phase 1 support.
#define MODE_P25
// Enable NXDN support, the boxcar filter sometimes improves the performance of NXDN receive on some systems.
#define MODE_NXDN
#define USE_NXDN_BOXCAR
// Enable M17 support.
#define MODE_M17
// Enable POCSAG support.
#define MODE_POCSAG
// Enable FM support.
#define MODE_FM
// Enable AX.25 support, this is only enabled if FM is also enabled.
#define MODE_AX25
// Allow for the use of high quality external clock oscillators
// The number is the frequency of the oscillator in Hertz.
//
// The frequency of the TCXO must be an integer multiple of 48000.
// Frequencies such as 12.0 Mhz (48000 * 250) and 14.4 Mhz (48000 * 300) are suitable.
// Frequencies such as 10.0 Mhz (48000 * 208.333) or 20 Mhz (48000 * 416.666) are not suitable.
//
// For 12 MHz
#define EXTERNAL_OSC 12000000
// For 12.288 MHz
// #define EXTERNAL_OSC 12288000
// For 14.4 MHz
// #define EXTERNAL_OSC 14400000
// For 19.2 MHz
// #define EXTERNAL_OSC 19200000
// Select a baud rate for host communication. The faster speeds are needed for external FM to work.
// #define SERIAL_SPEED 115200 // Suitable for most older boards (Arduino Due, STM32F1_POG, etc). External FM will NOT work with this!
// #define SERIAL_SPEED 230400 // Only works on newer boards like fast M4, M7, Teensy 3.x. External FM might work with this
#define SERIAL_SPEED 460800 // Only works on newer boards like fast M4, M7, Teensy 3.x. External FM should work with this
// Use pins to output the current mode via LEDs
#define MODE_LEDS
// For the original Arduino Due pin layout
// #define ARDUINO_DUE_PAPA
#if defined(STM32F1)
// For the SQ6POG board
#define STM32F1_POG
#else
// For the ZUM V1.0 and V1.0.1 boards pin layout
// #define ARDUINO_DUE_ZUM_V10
#endif
// For the SP8NTH board
// #define ARDUINO_DUE_NTH
// For ST Nucleo-64 STM32F446RE board
// #define STM32F4_NUCLEO_MORPHO_HEADER
// #define STM32F4_NUCLEO_ARDUINO_HEADER
// Use separate mode pins to switch external channel/filters/bandwidth for example
// #define MODE_PINS
// For the VK6MST Pi3 Shield communicating over i2c. i2c address & speed defined in i2cTeensy.cpp
// #define VK6MST_TEENSY_PI3_SHIELD_I2C
// Pass RSSI information to the host
#define SEND_RSSI_DATA
// Use the modem as a serial repeater for Nextion displays
#define SERIAL_REPEATER
// Use the modem as an I2C repeater for OLED displays
// #define I2C_REPEATER
// To reduce CPU load, you can remove the DC blocker by commenting out the next line
#define USE_DCBLOCKER
// Constant Service LED once repeater is running
// Do not use if employing an external hardware watchdog
// #define CONSTANT_SRV_LED
// Use the YSF and P25 LEDs for NXDN
// #define USE_ALTERNATE_NXDN_LEDS
// Use the D-Star and P25 LEDs for M17
#define USE_ALTERNATE_M17_LEDS
// Use the D-Star and DMR LEDs for POCSAG
#define USE_ALTERNATE_POCSAG_LEDS
// Use the D-Star and YSF LEDs for FM
#define USE_ALTERNATE_FM_LEDS
#if defined(STM32F1_POG)
// Slower boards need to run their serial at 115200 baud
#undef SERIAL_SPEED
#define SERIAL_SPEED 115200
#endif
#endif