masscan.8

.\" generated with Ronn/v0.7.3
.\" http://github.com/rtomayko/ronn/tree/0.7.3
.
.TH "MASSCAN" "8" "September 2013" "" ""
.
.SH "NAME"
\fBmasscan\fR \- Fast scan of the Internet
.
.SH "SYNOPSIS"
masscan <ip addresses/ranges> \-p \fIports\fR \fIoptions\fR
.
.SH "DESCRIPTION"
\fBmasscan\fR is an Internet\-scale port scanner, useful for large scale surveys of the Internet, or of internal networks\. While the default transmit rate is only 100 packets/second, it can optional go as fast as 25 million packets/second, a rate sufficient to scan the Internet in 3 minutes for one port\.
.
.SH "OPTIONS"
.
.IP "\(bu" 4
\fB<ip/range>\fR: anything on the command\-line not prefixed with a \'\-\' is assumed to be an IP address or range\. There are three valid formats\. The first is a single IPv4 address like "192\.168\.0\.1"\. The second is a range like "10\.0\.0\.1\-10\.0\.0\.100"\. The third is a CIDR address, like "0\.0\.0\.0/0"\. At least one target must be specified\. Multiple targets can be specified\. This can be specified as multiple options separated by space, or can be separated by a comma as a single option, such as \fB10\.0\.0\.0/8,192\.168\.0\.1\fR\.
.
.IP "\(bu" 4
\fB\-\-range <ip/range>\fR: the same as target range spec described above, except as a named parameter instead of an unnamed one\.
.
.IP "\(bu" 4
\fB\-p <ports\fR, \fB\-\-ports <ports>\fR: specifies the port(s) to be scanned\. A single port can be specified, like \fB\-p80\fR\. A range of ports can be specified, like \fB\-p 20\-25\fR\. A list of ports/ranges can be specified, like \fB\-p80,20\-25\fR\. UDP ports can also be specified, like \fB\-\-ports U:161,U:1024\-1100\fR\.
.
.IP "\(bu" 4
\fB\-\-banners\fR: specifies that banners should be grabbed, like HTTP server versions, HTML title fields, and so forth\. Only a few protocols are supported\.
.
.IP "\(bu" 4
\fB\-\-rate <packets\-per\-second>\fR: specifies the desired rate for transmitting packets\. This can be very small numbers, like \fB0\.1\fR for transmitting packets at rates of one every 10 seconds, for very large numbers like 10000000, which attempts to transmit at 10 million packets/second\. In my experience, Windows and can do 250 thousand packets per second, and latest versions of Linux can do 2\.5 million packets per second\. The PF_RING driver is needed to get to 25 million packets/second\.
.
.IP "\(bu" 4
\fB\-c <filename>\fR, \fB\-\-conf <filename>\fR: reads in a configuration file\. The format of the configuration file is described below\.
.
.IP "\(bu" 4
\fB\-\-resume <filename>\fR: the same as \fB\-\-conf\fR, except that a few options are automatically set, such as \fB\-\-append\-output\fR\. The format of the configuration file is described below\.
.
.IP "\(bu" 4
\fB\-\-echo\fR: don\'t run, but instead dump the current configuration to a file\. This file can then be used with the \fB\-c\fR option\. The format of this output is described below under \'CONFIGURATION FILE\'\.
.
.IP "\(bu" 4
\fB\-e <ifname>\fR, \fB\-\-adapter <ifname>\fR: use the named raw network interface, such as "eth0" or "dna1"\. If not specified, the first network interface found with a default gateway will be used\.
.
.IP "\(bu" 4
\fB\-\-adapter\-ip <ip\-address>\fR: send packets using this IP address\. If not specified, then the first IP address bound to the network interface will be used\.
.
.IP "\(bu" 4
\fB\-\-adapter\-port <ip\-address>\fR: send packets using this port number as the source\. If not specified, a random port will be chosen in the range 40000 through 60000\. This port should be filtered by the host firewall (like iptables) to prevent the host network stack from interfering with arriving packets\.
.
.IP "\(bu" 4
\fB\-\-adapter\-mac <mac\-address>\fR: send packets using this as the source MAC address\. If not specified, then the first MAC address bound to the network interface will be used\.
.
.IP "\(bu" 4
\fB\-\-router\-mac <mac address>\fR: send packets to this MAC address as the destination\. If not specified, then the gateway address of the network interface will be ARPed\.
.
.IP "\(bu" 4
\fB\-\-ping\fR: indicates that the scan should include an ICMP echo request\. This may be included with TCP and UDP scanning\.
.
.IP "\(bu" 4
\fB\-\-exclude <ip/range>\fR: blacklist an IP address or range, preventing it from being scanned\. This overrides any target specification, guaranteeing that this address/range won\'t be scanned\. This has the same format as the normal target specification\.
.
.IP "\(bu" 4
\fB\-\-excludefile <filename>\fR: reads in a list of exclude ranges, in the same target format described above\. These ranges override any targets, preventing them from being scanned\.
.
.IP "\(bu" 4
\fB\-\-append\-output\fR: causes output to append to file, rather than overwriting the file\.
.
.IP "\(bu" 4
\fB\-\-iflist\fR: list the available network interfaces, and then exits\.
.
.IP "\(bu" 4
\fB\-\-retries\fR: the number of retries to send, at 1 second intervals\. Note that since this scanner is stateless, retries are sent regardless if replies have already been received\.
.
.IP "\(bu" 4
\fB\-\-nmap\fR: print help aobut nmap\-compatibility alternatives for these options\.
.
.IP "\(bu" 4
\fB\-\-pcap\-payloads\fR: read packets from a libpcap file containing packets and extract the UDP payloads, and associate those payloads with the destination port\. These payloads will then be used when sending UDP packets with the matching destination port\. Only one payload will be remembered per port\. Similar to \fB\-\-nmap\-payloads\fR\.
.
.IP "\(bu" 4
\fB\-\-nmap\-payloads <filename>\fR: read in a file in the same format as the nmap file \fBnmap\-payloads\fR\. This contains UDP payload, so that we can send useful UDP packets instead of empty ones\. Similar to \fB\-\-pcap\-payloads\fR\.
.
.IP "\(bu" 4
\fB\-\-open\-only\fR: report only open ports, not closed ports\.
.
.IP "\(bu" 4
\fB\-\-output\-format <fmt>\fR: indicates the format of the output file, which can be \fBxml\fR or \fBbinary\fR\. The option \fB\-\-output\-filename\fR must be specified\.
.
.IP "\(bu" 4
\fB\-\-output\-filename <filename>\fR: the file which to save results to\. If the parameter \fB\-\-output\-format\fR is not specified, then the default of \fBxml\fR will be used\.
.
.IP "\(bu" 4
\fB\-\-pcap <filename>\fR: saves received packets (but not transmitted packets) to the libpcap\-format file\.
.
.IP "\(bu" 4
\fB\-\-packet\-trace\fR: prints a summary of those packets sent and received\. This is useful at low rates, like a few packets per second, but will overwhelm the terminal at high rates\.
.
.IP "\(bu" 4
\fB\-\-pfring\fR: force the use of the PF_RING driver\. The program will exit if PF_RING DNA drvers are not available\.
.
.IP "\(bu" 4
\fB\-\-resume\-index\fR: the point in the scan at when it was paused\.
.
.IP "\(bu" 4
\fB\-\-resume\-count\fR: the maximum number of probes to send before exiting\. This is useful with the \fB\-\-resume\-index\fR to chop up a scan and split it among multiple instances, though the \fB\-\-shards\fR option might be better\.
.
.IP "\(bu" 4
\fB\-\-shards <x>/<y>\fR: splits the scan among instances\. \fBx\fR is the id for this scan, while \fBy\fR is the total number of instances\. For example, \fB\-\-shards 1/2\fR tells an instance to send every other packet, starting with index 0\. Likewise, \fB\-\-shards 2/2\fR sends every other packet, but starting with index 1, so that it doesn\'t overlap with the first example\.
.
.IP "\(bu" 4
\fB\-\-rotate <time>\fR: rotates the output file, renaming it with the current timestamp, moving it to a separate directory\. The time is specified in number of seconds, like "3600" for an hour\. Or, units of time can be specified, such as "hourly", or "6hours", or "10min"\. Times are aligned on an even boundary, so if "daily" is specified, then the file will be rotated every day at midnight\.
.
.IP "\(bu" 4
\fB\-\-rotate\-offset <time>\fR: an offset in the time\. This is to accomodate timezones\.
.
.IP "\(bu" 4
\fB\-\-rotate\-dir <directory>\fR: when rotating the file, this specifies which directory to move the file to\. A useful directory is \fB/var/log/masscan\fR\.
.
.IP "\(bu" 4
\fB\-\-seed <integer>\fR: an integer that seeds the random number generator\. Using a different seed will cause packets to be sent in a different random order\. Instead of an integer, the string \fBtime\fR can be specified, which seeds using the local timestamp, automatically generating a differnet random order of scans\.
.
.IP "\(bu" 4
\fB\-\-regress\fR: run a regression test, returns \'0\' on success and \'1\' on failure\.
.
.IP "\(bu" 4
\fB\-\-ttl <num>\fR: specifies the TTL of outgoing packets, defaults to 255\.
.
.IP "\(bu" 4
\fB\-\-wait <seconds>\fR: specifies the number of seconds after transmit is done to wait for receiving packets before exiting the program\. The default is 10 seconds\. The string \fBforever\fR can be specified to never terminate\.
.
.IP "\(bu" 4
\fB\-\-offline\fR: don\'t actually transmit packets\. This is useful with a low rate and \fB\-\-packet\-trace\fR to look at what packets might\'ve been transmitted\. Or, it\'s useful with \fB\-\-rate 100000000\fR in order to benchmark how fast transmit would work (assuming a zero\-overhead driver)\. PF_RING is about 20% slower than the benchmark result from offline mode\.
.
.IP "\(bu" 4
\fB\-sL\fR: this doesn\'t do a scan, but instead creates a list of random addresses\. This is useful for importing into other tools\. The options \fB\-\-shard\fR, \fB\-\-resume\-index\fR, and \fB\-\-resume\-count\fR can be useful with this feature\.
.
.IP "\(bu" 4
\fB\-oX <filename>\fR: sets the output format to XML and saves the output in the given filename\. This is equivelent to using the \fB\-\-output\-format\fR and \fB\-\-output\-filename\fR parameters\.
.
.IP "\(bu" 4
\fB\-oB <filename>\fR: sets the output format to binary and saves the output in the given filename\. This is equivelent to using the \fB\-\-output\-format\fR and \fB\-\-output\-filename\fR parameters\. The tool \fBscan2text\fR can then be used to read the binary file\. Binary files are mush smaller than their XML equivelents, but require a separate step to convert back into XML or another readable format\.
.
.IP "" 0
.
.SH "CONFIGURATION FILE FORMAT"
The configuration file uses the same parameter names as on the commandline, but without the \fB\-\-\fR prefix, and with an \fB=\fR sign between the name and the value\. An example configuration file might be:
.
.IP "" 4
.
.nf

# targets
range = 10\.0\.0\.0/8,192\.168\.0\.0/16
range = 172\.16\.0\.0/14
ports = 20\-25,80,U:53
ping = true

# adapter
adapter = eth0
adapter\-ip = 192\.168\.0\.1
router\-mac = 66\-55\-44\-33\-22\-11

# other
exclude\-file = /etc/masscan/exludes\.txt
.
.fi
.
.IP "" 0
.
.P
By default, the program will read default configuration from the file \fB/etc/masscan/masscan\.conf\fR\. This is useful for system\-specific settings, such as the \fB\-\-adapter\-xxx\fR options\. This is also useful for excluded IP addresses, so that you can scan the entire Internet, while skipping dangerous addresses, like those owned by the DoD, and not make an accidental mistake\.
.
.SH "CONTROL\-C BEHAVIOR"
When the user presses \fIctrl\-c\fR, the scan will stop, and the current state of the scan will be saved in the file \'paused\.conf\'\. The scan can be resumed with the \fB\-\-resume\fR option:
.
.IP "" 4
.
.nf

# masscan \-\-resume paused\.conf
.
.fi
.
.IP "" 0
.
.P
The program will not exit immediately, but will wait a default of 10 seconds to receive results from the Internet and save the results before exiting completely\. This time can be changed with the \fB\-\-wait\fR option\.
.
.SH "SIMPLE EXAMPLES"
The following example scans all private networks for webservers, and prints all open ports that were found\.
.
.IP "" 4
.
.nf

# masscan 10\.0\.0\.0/8 192\.168\.0\.0/16 172\.16\.0\.0/12 \-p80 \-\-open\-only
.
.fi
.
.IP "" 0
.
.P
The following example scans the entire Internet for DNS servers, grabbing their versions, then saves the results in an XML file\.
.
.IP "" 4
.
.nf

# masscan 0\.0\.0\.0/0 \-\-excludefile no\-dod\.txt \-pU:53 \-\-banners \-\-output\-filename dns\.xml
.
.fi
.
.IP "" 0
.
.P
You should be able to import the XML into databases and such\.
.
.SH "ADVANCED EXAMPLES"
Let\'s say that you want to scan the entire Internet and spread the scan across three machines\. Masscan would be launched on all three machines using the following command\-lines:
.
.IP "" 4
.
.nf

# masscan 0\.0\.0\.0/0 \-p0\-65535 \-\-shard 1/3
# masscan 0\.0\.0\.0/0 \-p0\-65535 \-\-shard 2/3
# masscan 0\.0\.0\.0/0 \-p0\-65535 \-\-shard 3/3
.
.fi
.
.IP "" 0
.
.P
An alternative is with the "resume" feature\. A scan has an internal index that goes from zero to the number of ports times then number of IP addresses\. The following example shows splitting up a scan into chunks of a 1000 items each:
.
.IP "" 4
.
.nf

# masscan 0\.0\.0\.0/0 \-p0\-65535 \-\-resume\-index 0 \-\-resume\-count 1000
# masscan 0\.0\.0\.0/0 \-p0\-65535 \-\-resume\-index 1000 \-\-resume\-count 1000
# masscan 0\.0\.0\.0/0 \-p0\-65535 \-\-resume\-index 2000 \-\-resume\-count 1000
# masscan 0\.0\.0\.0/0 \-p0\-65535 \-\-resume\-index 3000 \-\-resume\-count 1000
.
.fi
.
.IP "" 0
.
.P
A script can use this to split smaller tasks across many other machines, such as Amazon EC2 instances\. As each instance completes a job, the script might send a request to a central coordinating server for more work\.
.
.SH "SPURIOUS RESETS"
When scanning TCP using the default IP address of your adapter, the built\-in stack will generate RST packets\. This will prevent banner grabbing\. There are are two ways to solve this\. The first way is to create a firewall rule to block that port from being seen by the stack\. How this works is dependent on the operating system, but on Linux this looks something like:
.
.IP "" 4
.
.nf

# iptables \-A INPUT \-p tcp \-i eth0 \-\-dport 61234 \-j DROP
.
.fi
.
.IP "" 0
.
.P
Then, when scanning, that same port must be used as the source:
.
.IP "" 4
.
.nf

# masscan 10\.0\.0\.0/8 \-p80 \-\-banners \-\-adapter\-port 61234
.
.fi
.
.IP "" 0
.
.P
An alternative is to "spoof" a different IP address\. This IP address must be within the range of the local network, but must not otherwise be in use by either your own computer or another computer on the network\. An example of this would look like:
.
.IP "" 4
.
.nf

# masscan 10\.0\.0\.0/8 \-p80 \-\-banners \-\-adapter\-ip 192\.168\.1\.101
.
.fi
.
.IP "" 0
.
.P
Setting your source IP address this way is the preferred way of running this scanner\.
.
.SH "ABUSE COMPLAINTS"
This scanner is designed for large\-scale surveys, of either an organization, or of the Internet as a whole\. This scanning will be noticed by those monitoring their logs, which will generate complaints\.
.
.P
If you are scanning your own organization, this may lead to you being fired\. Never scan outside your local subnet without getting permission from your boss, with a clear written declaration of why you are scanning\.
.
.P
The same applies to scanning the Internet from your employer\. This is another good way to get fired, as your IT department gets flooded with complaints as to why your organization is hacking them\.
.
.P
When scanning on your own, such as your home Internet or ISP, this will likely cause them to cancel your account due to the abuse complaints\.
.
.P
One solution is to work with your ISP, to be clear about precisely what we are doing, to prove to them that we are researching the Internet, not "hacking" it\. We have our ISP send the abuse complaints directly to us\. For anyone that asks, we add them to our "\-\-excludefile", blacklisting them so that we won\'t scan them again\. While interacting with such people, some instead add us to their whitelist, so that their firewalls won\'t log us anymore (they\'ll still block us, of course, they just won\'t log that fact to avoid filling up their logs with our scans)\.
.
.P
Ultimately, I don\'t know if it\'s possible to completely solve this problem\. Despite the Internet being a public, end\-to\-end network, you are still "guilty until proven innocent" when you do a scan\.
.
.SH "COMPATIBILITY"
While not listed in this document, a lot of parameters compatible with \fBnmap\fR will also work\.
.
.SH "SEE ALSO"
nmap(8), pcap(3)
.
.SH "AUTHORS"
This tool was written by Robert Graham\. The source code is available at https://github\.com/robertdavidgraham/masscan\.