forked from u-boot/u-boot
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathREADME
3128 lines (2411 loc) · 104 KB
/
README
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
#
# (C) Copyright 2000 - 2002
# Wolfgang Denk, DENX Software Engineering, [email protected].
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
Summary:
========
This directory contains the source code for U-Boot, a boot loader for
Embedded boards based on PowerPC and ARM processors, which can be
installed in a boot ROM and used to initialize and test the hardware
or to download and run application code.
The development of U-Boot is closely related to Linux: some parts of
the source code originate in the Linux source tree, we have some
header files in common, and special provision has been made to
support booting of Linux images.
Some attention has been paid to make this software easily
configurable and extendable. For instance, all monitor commands are
implemented with the same call interface, so that it's very easy to
add new commands. Also, instead of permanently adding rarely used
code (for instance hardware test utilities) to the monitor, you can
load and run it dynamically.
Status:
=======
In general, all boards for which a configuration option exists in the
Makefile have been tested to some extent and can be considered
"working". In fact, many of them are used in production systems.
In case of problems see the CHANGELOG and CREDITS files to find out
who contributed the specific port.
Where to get help:
==================
In case you have questions about, problems with or contributions for
U-Boot you should send a message to the U-Boot mailing list at
<[email protected]>. There is also an archive of
previous traffic on the mailing list - please search the archive
before asking FAQ's. Please see
http://lists.sourceforge.net/lists/listinfo/u-boot-users/
Where we come from:
===================
- start from 8xxrom sources
- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
- clean up code
- make it easier to add custom boards
- make it possible to add other [PowerPC] CPUs
- extend functions, especially:
* Provide extended interface to Linux boot loader
* S-Record download
* network boot
* PCMCIA / CompactFLash / ATA disk / SCSI ... boot
- create ARMBoot project (http://sourceforge.net/projects/armboot)
- add other CPU families (starting with ARM)
- create U-Boot project (http://sourceforge.net/projects/u-boot)
Names and Spelling:
===================
The "official" name of this project is "Das U-Boot". The spelling
"U-Boot" shall be used in all written text (documentation, comments
in source files etc.). Example:
This is the README file for the U-Boot project.
File names etc. shall be based on the string "u-boot". Examples:
include/asm-ppc/u-boot.h
#include <asm/u-boot.h>
Variable names, preprocessor constants etc. shall be either based on
the string "u_boot" or on "U_BOOT". Example:
U_BOOT_VERSION u_boot_logo
IH_OS_U_BOOT u_boot_hush_start
Versioning:
===========
U-Boot uses a 3 level version number containing a version, a
sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
sub-version "34", and patchlevel "4".
The patchlevel is used to indicate certain stages of development
between released versions, i. e. officially released versions of
U-Boot will always have a patchlevel of "0".
Directory Hierarchy:
====================
- board Board dependend files
- common Misc architecture independend functions
- cpu CPU specific files
- disk Code for disk drive partition handling
- doc Documentation (don't expect too much)
- drivers Common used device drivers
- dtt Digital Thermometer and Thermostat drivers
- examples Example code for standalone applications, etc.
- include Header Files
- disk Harddisk interface code
- net Networking code
- ppc Files generic to PowerPC architecture
- post Power On Self Test
- post/arch Symlink to architecture specific Power On Self Test
- post/arch-ppc PowerPC architecture specific Power On Self Test
- post/cpu/mpc8260 MPC8260 CPU specific Power On Self Test
- post/cpu/mpc8xx MPC8xx CPU specific Power On Self Test
- rtc Real Time Clock drivers
- tools Tools to build S-Record or U-Boot images, etc.
- cpu/74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs
- cpu/arm925t Files specific to ARM 925 CPUs
- cpu/mpc5xx Files specific to Motorola MPC5xx CPUs
- cpu/mpc8xx Files specific to Motorola MPC8xx CPUs
- cpu/mpc824x Files specific to Motorola MPC824x CPUs
- cpu/mpc8260 Files specific to Motorola MPC8260 CPU
- cpu/ppc4xx Files specific to IBM 4xx CPUs
- board/LEOX/ Files specific to boards manufactured by The LEOX team
- board/LEOX/elpt860 Files specific to ELPT860 boards
- board/RPXClassic
Files specific to RPXClassic boards
- board/RPXlite Files specific to RPXlite boards
- board/at91rm9200dk Files specific to AT91RM9200DK boards
- board/c2mon Files specific to c2mon boards
- board/cmi Files specific to cmi boards
- board/cogent Files specific to Cogent boards
(need further configuration)
Files specific to CPCIISER4 boards
- board/cpu86 Files specific to CPU86 boards
- board/cray/ Files specific to boards manufactured by Cray
- board/cray/L1 Files specific to L1 boards
- board/cu824 Files specific to CU824 boards
- board/ebony Files specific to IBM Ebony board
- board/eric Files specific to ERIC boards
- board/esd/ Files specific to boards manufactured by ESD
- board/esd/adciop Files specific to ADCIOP boards
- board/esd/ar405 Files specific to AR405 boards
- board/esd/canbt Files specific to CANBT boards
- board/esd/cpci405 Files specific to CPCI405 boards
- board/esd/cpciiser4 Files specific to CPCIISER4 boards
- board/esd/common Common files for ESD boards
- board/esd/dasa_sim Files specific to DASA_SIM boards
- board/esd/du405 Files specific to DU405 boards
- board/esd/ocrtc Files specific to OCRTC boards
- board/esd/pci405 Files specific to PCI405 boards
- board/esteem192e
Files specific to ESTEEM192E boards
- board/etx094 Files specific to ETX_094 boards
- board/evb64260
Files specific to EVB64260 boards
- board/fads Files specific to FADS boards
- board/flagadm Files specific to FLAGADM boards
- board/gen860t Files specific to GEN860T and GEN860T_SC boards
- board/genietv Files specific to GENIETV boards
- board/gth Files specific to GTH boards
- board/hermes Files specific to HERMES boards
- board/hymod Files specific to HYMOD boards
- board/icu862 Files specific to ICU862 boards
- board/ip860 Files specific to IP860 boards
- board/iphase4539
Files specific to Interphase4539 boards
- board/ivm Files specific to IVMS8/IVML24 boards
- board/lantec Files specific to LANTEC boards
- board/lwmon Files specific to LWMON boards
- board/mbx8xx Files specific to MBX boards
- board/mpc8260ads
Files specific to MPC8260ADS and PQ2FADS-ZU boards
- board/mpl/ Files specific to boards manufactured by MPL
- board/mpl/common Common files for MPL boards
- board/mpl/pip405 Files specific to PIP405 boards
- board/mpl/mip405 Files specific to MIP405 boards
- board/musenki Files specific to MUSEKNI boards
- board/mvs1 Files specific to MVS1 boards
- board/nx823 Files specific to NX823 boards
- board/oxc Files specific to OXC boards
- board/omap1510inn
Files specific to OMAP 1510 Innovator boards
- board/pcippc2 Files specific to PCIPPC2/PCIPPC6 boards
- board/pm826 Files specific to PM826 boards
- board/ppmc8260
Files specific to PPMC8260 boards
- board/rpxsuper
Files specific to RPXsuper boards
- board/rsdproto
Files specific to RSDproto boards
- board/sandpoint
Files specific to Sandpoint boards
- board/sbc8260 Files specific to SBC8260 boards
- board/sacsng Files specific to SACSng boards
- board/siemens Files specific to boards manufactured by Siemens AG
- board/siemens/CCM Files specific to CCM boards
- board/siemens/IAD210 Files specific to IAD210 boards
- board/siemens/SCM Files specific to SCM boards
- board/siemens/pcu_e Files specific to PCU_E boards
- board/sixnet Files specific to SIXNET boards
- board/spd8xx Files specific to SPD8xxTS boards
- board/tqm8260 Files specific to TQM8260 boards
- board/tqm8xx Files specific to TQM8xxL boards
- board/w7o Files specific to W7O boards
- board/walnut405
Files specific to Walnut405 boards
- board/westel/ Files specific to boards manufactured by Westel Wireless
- board/westel/amx860 Files specific to AMX860 boards
- board/utx8245 Files specific to UTX8245 boards
Software Configuration:
=======================
Configuration is usually done using C preprocessor defines; the
rationale behind that is to avoid dead code whenever possible.
There are two classes of configuration variables:
* Configuration _OPTIONS_:
These are selectable by the user and have names beginning with
"CONFIG_".
* Configuration _SETTINGS_:
These depend on the hardware etc. and should not be meddled with if
you don't know what you're doing; they have names beginning with
"CFG_".
Later we will add a configuration tool - probably similar to or even
identical to what's used for the Linux kernel. Right now, we have to
do the configuration by hand, which means creating some symbolic
links and editing some configuration files. We use the TQM8xxL boards
as an example here.
Selection of Processor Architecture and Board Type:
---------------------------------------------------
For all supported boards there are ready-to-use default
configurations available; just type "make <board_name>_config".
Example: For a TQM823L module type:
cd u-boot
make TQM823L_config
For the Cogent platform, you need to specify the cpu type as well;
e.g. "make cogent_mpc8xx_config". And also configure the cogent
directory according to the instructions in cogent/README.
Configuration Options:
----------------------
Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/<board_name>.h".
Example: For a TQM823L module, all configuration settings are in
"include/configs/TQM823L.h".
Many of the options are named exactly as the corresponding Linux
kernel configuration options. The intention is to make it easier to
build a config tool - later.
The following options need to be configured:
- CPU Type: Define exactly one of
PowerPC based CPUs:
-------------------
CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
or CONFIG_MPC5xx
or CONFIG_MPC824X, CONFIG_MPC8260
or CONFIG_IOP480
or CONFIG_405GP
or CONFIG_440
or CONFIG_MPC74xx
or CONFIG_750FX
ARM based CPUs:
---------------
CONFIG_SA1110
CONFIG_ARM7
CONFIG_PXA250
- Board Type: Define exactly one of
PowerPC based boards:
---------------------
CONFIG_ADCIOP, CONFIG_ICU862 CONFIG_RPXsuper,
CONFIG_ADS860, CONFIG_IP860, CONFIG_SM850,
CONFIG_AMX860, CONFIG_IPHASE4539, CONFIG_SPD823TS,
CONFIG_AR405, CONFIG_IVML24, CONFIG_SXNI855T,
CONFIG_BAB7xx, CONFIG_IVML24_128, CONFIG_Sandpoint8240,
CONFIG_CANBT, CONFIG_IVML24_256, CONFIG_Sandpoint8245,
CONFIG_CCM, CONFIG_IVMS8, CONFIG_TQM823L,
CONFIG_CPCI405, CONFIG_IVMS8_128, CONFIG_TQM850L,
CONFIG_CPCI4052, CONFIG_IVMS8_256, CONFIG_TQM855L,
CONFIG_CPCIISER4, CONFIG_LANTEC, CONFIG_TQM860L,
CONFIG_CPU86, CONFIG_MBX, CONFIG_TQM8260,
CONFIG_CRAYL1, CONFIG_MBX860T, CONFIG_TTTech,
CONFIG_CU824, CONFIG_MHPC, CONFIG_UTX8245,
CONFIG_DASA_SIM, CONFIG_MIP405, CONFIG_W7OLMC,
CONFIG_DU405, CONFIG_MOUSSE, CONFIG_W7OLMG,
CONFIG_ELPPC, CONFIG_MPC8260ADS, CONFIG_WALNUT405,
CONFIG_ERIC, CONFIG_MUSENKI, CONFIG_ZUMA,
CONFIG_ESTEEM192E, CONFIG_MVS1, CONFIG_c2mon,
CONFIG_ETX094, CONFIG_NX823, CONFIG_cogent_mpc8260,
CONFIG_EVB64260, CONFIG_OCRTC, CONFIG_cogent_mpc8xx,
CONFIG_FADS823, CONFIG_ORSG, CONFIG_ep8260,
CONFIG_FADS850SAR, CONFIG_OXC, CONFIG_gw8260,
CONFIG_FADS860T, CONFIG_PCI405, CONFIG_hermes,
CONFIG_FLAGADM, CONFIG_PCIPPC2, CONFIG_hymod,
CONFIG_FPS850L, CONFIG_PCIPPC6, CONFIG_lwmon,
CONFIG_GEN860T, CONFIG_PIP405, CONFIG_pcu_e,
CONFIG_GENIETV, CONFIG_PM826, CONFIG_ppmc8260,
CONFIG_GTH, CONFIG_RPXClassic, CONFIG_rsdproto,
CONFIG_IAD210, CONFIG_RPXlite, CONFIG_sbc8260,
CONFIG_EBONY, CONFIG_sacsng, CONFIG_FPS860L,
CONFIG_V37, CONFIG_ELPT860, CONFIG_CMI,
CONFIG_NETVIA, CONFIG_RBC823
ARM based boards:
-----------------
CONFIG_HHP_CRADLE, CONFIG_DNP1110, CONFIG_EP7312,
CONFIG_IMPA7, CONFIG_LART, CONFIG_LUBBOCK,
CONFIG_INNOVATOROMAP1510,
CONFIG_SHANNON, CONFIG_SMDK2400, CONFIG_SMDK2410,
CONFIG_TRAB, CONFIG_AT91RM9200DK
- CPU Module Type: (if CONFIG_COGENT is defined)
Define exactly one of
CONFIG_CMA286_60_OLD
--- FIXME --- not tested yet:
CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
CONFIG_CMA287_23, CONFIG_CMA287_50
- Motherboard Type: (if CONFIG_COGENT is defined)
Define exactly one of
CONFIG_CMA101, CONFIG_CMA102
- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
Define one or more of
CONFIG_CMA302
- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
Define one or more of
CONFIG_LCD_HEARTBEAT - update a character position on
the lcd display every second with
a "rotator" |\-/|\-/
- Board flavour: (if CONFIG_MPC8260ADS is defined)
CONFIG_ADSTYPE
Possible values are:
CFG_8260ADS - original MPC8260ADS
CFG_8266ADS - MPC8266ADS (untested)
CFG_PQ2FADS - PQ2FADS-ZU
- MPC824X Family Member (if CONFIG_MPC824X is defined)
Define exactly one of
CONFIG_MPC8240, CONFIG_MPC8245
- 8xx CPU Options: (if using an 8xx cpu)
Define one or more of
CONFIG_8xx_GCLK_FREQ - if get_gclk_freq() can not work e.g.
no 32KHz reference PIT/RTC clock
- Clock Interface:
CONFIG_CLOCKS_IN_MHZ
U-Boot stores all clock information in Hz
internally. For binary compatibility with older Linux
kernels (which expect the clocks passed in the
bd_info data to be in MHz) the environment variable
"clocks_in_mhz" can be defined so that U-Boot
converts clock data to MHZ before passing it to the
Linux kernel.
When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
"clocks_in_mhz=1" is automatically included in the
default environment.
- Console Interface:
Depending on board, define exactly one serial port
(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
console by defining CONFIG_8xx_CONS_NONE
Note: if CONFIG_8xx_CONS_NONE is defined, the serial
port routines must be defined elsewhere
(i.e. serial_init(), serial_getc(), ...)
CONFIG_CFB_CONSOLE
Enables console device for a color framebuffer. Needs following
defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
(default big endian)
VIDEO_HW_RECTFILL graphic chip supports
rectangle fill
(cf. smiLynxEM)
VIDEO_HW_BITBLT graphic chip supports
bit-blit (cf. smiLynxEM)
VIDEO_VISIBLE_COLS visible pixel columns
(cols=pitch)
VIDEO_VISIBLE_ROWS visible pixel rows
VIDEO_PIXEL_SIZE bytes per pixel
VIDEO_DATA_FORMAT graphic data format
(0-5, cf. cfb_console.c)
VIDEO_FB_ADRS framebuffer address
VIDEO_KBD_INIT_FCT keyboard int fct
(i.e. i8042_kbd_init())
VIDEO_TSTC_FCT test char fct
(i.e. i8042_tstc)
VIDEO_GETC_FCT get char fct
(i.e. i8042_getc)
CONFIG_CONSOLE_CURSOR cursor drawing on/off
(requires blink timer
cf. i8042.c)
CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
CONFIG_CONSOLE_TIME display time/date info in
upper right corner
(requires CFG_CMD_DATE)
CONFIG_VIDEO_LOGO display Linux logo in
upper left corner
CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
linux_logo.h for logo.
Requires CONFIG_VIDEO_LOGO
CONFIG_CONSOLE_EXTRA_INFO
addional board info beside
the logo
When CONFIG_CFB_CONSOLE is defined, video console is
default i/o. Serial console can be forced with
environment 'console=serial'.
- Console Baudrate:
CONFIG_BAUDRATE - in bps
Select one of the baudrates listed in
CFG_BAUDRATE_TABLE, see below.
- Interrupt driven serial port input:
CONFIG_SERIAL_SOFTWARE_FIFO
PPC405GP only.
Use an interrupt handler for receiving data on the
serial port. It also enables using hardware handshake
(RTS/CTS) and UART's built-in FIFO. Set the number of
bytes the interrupt driven input buffer should have.
Set to 0 to disable this feature (this is the default).
This will also disable hardware handshake.
- Console UART Number:
CONFIG_UART1_CONSOLE
IBM PPC4xx only.
If defined internal UART1 (and not UART0) is used
as default U-Boot console.
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
See doc/README.autoboot for these options that
work with CONFIG_BOOTDELAY. None are required.
CONFIG_BOOT_RETRY_TIME
CONFIG_BOOT_RETRY_MIN
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_DELAY_STR
CONFIG_AUTOBOOT_STOP_STR
CONFIG_AUTOBOOT_DELAY_STR2
CONFIG_AUTOBOOT_STOP_STR2
CONFIG_ZERO_BOOTDELAY_CHECK
CONFIG_RESET_TO_RETRY
- Autoboot Command:
CONFIG_BOOTCOMMAND
Only needed when CONFIG_BOOTDELAY is enabled;
define a command string that is automatically executed
when no character is read on the console interface
within "Boot Delay" after reset.
CONFIG_BOOTARGS
This can be used to pass arguments to the bootm
command. The value of CONFIG_BOOTARGS goes into the
environment value "bootargs".
CONFIG_RAMBOOT and CONFIG_NFSBOOT
The value of these goes into the environment as
"ramboot" and "nfsboot" respectively, and can be used
as a convenience, when switching between booting from
ram and nfs.
- Pre-Boot Commands:
CONFIG_PREBOOT
When this option is #defined, the existence of the
environment variable "preboot" will be checked
immediately before starting the CONFIG_BOOTDELAY
countdown and/or running the auto-boot command resp.
entering interactive mode.
This feature is especially useful when "preboot" is
automatically generated or modified. For an example
see the LWMON board specific code: here "preboot" is
modified when the user holds down a certain
combination of keys on the (special) keyboard when
booting the systems
- Serial Download Echo Mode:
CONFIG_LOADS_ECHO
If defined to 1, all characters received during a
serial download (using the "loads" command) are
echoed back. This might be needed by some terminal
emulations (like "cu"), but may as well just take
time on others. This setting #define's the initial
value of the "loads_echo" environment variable.
- Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
CONFIG_KGDB_BAUDRATE
Select one of the baudrates listed in
CFG_BAUDRATE_TABLE, see below.
- Monitor Functions:
CONFIG_COMMANDS
Most monitor functions can be selected (or
de-selected) by adjusting the definition of
CONFIG_COMMANDS; to select individual functions,
#define CONFIG_COMMANDS by "OR"ing any of the
following values:
#define enables commands:
-------------------------
CFG_CMD_ASKENV * ask for env variable
CFG_CMD_BDI bdinfo
CFG_CMD_BEDBUG Include BedBug Debugger
CFG_CMD_BOOTD bootd
CFG_CMD_CACHE icache, dcache
CFG_CMD_CONSOLE coninfo
CFG_CMD_DATE * support for RTC, date/time...
CFG_CMD_DHCP DHCP support
CFG_CMD_ECHO * echo arguments
CFG_CMD_EEPROM * EEPROM read/write support
CFG_CMD_ELF bootelf, bootvx
CFG_CMD_ENV saveenv
CFG_CMD_FDC * Floppy Disk Support
CFG_CMD_FAT FAT partition support
CFG_CMD_FDOS * Dos diskette Support
CFG_CMD_FLASH flinfo, erase, protect
CFG_CMD_FPGA FPGA device initialization support
CFG_CMD_I2C * I2C serial bus support
CFG_CMD_IDE * IDE harddisk support
CFG_CMD_IMI iminfo
CFG_CMD_IMMAP * IMMR dump support
CFG_CMD_IRQ * irqinfo
CFG_CMD_KGDB * kgdb
CFG_CMD_LOADB loadb
CFG_CMD_LOADS loads
CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, mtest
CFG_CMD_MMC MMC memory mapped support
CFG_CMD_MII MII utility commands
CFG_CMD_NET bootp, tftpboot, rarpboot
CFG_CMD_PCI * pciinfo
CFG_CMD_PCMCIA * PCMCIA support
CFG_CMD_REGINFO * Register dump
CFG_CMD_RUN run command in env variable
CFG_CMD_SCSI * SCSI Support
CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
CFG_CMD_SPI * SPI serial bus support
CFG_CMD_USB * USB support
CFG_CMD_BSP * Board SPecific functions
-----------------------------------------------
CFG_CMD_ALL all
CFG_CMD_DFL Default configuration; at the moment
this is includes all commands, except
the ones marked with "*" in the list
above.
If you don't define CONFIG_COMMANDS it defaults to
CFG_CMD_DFL in include/cmd_confdefs.h. A board can
override the default settings in the respective
include file.
EXAMPLE: If you want all functions except of network
support you can write:
#define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
Note: Don't enable the "icache" and "dcache" commands
(configuration option CFG_CMD_CACHE) unless you know
what you (and your U-Boot users) are doing. Data
cache cannot be enabled on systems like the 8xx or
8260 (where accesses to the IMMR region must be
uncached), and it cannot be disabled on all other
systems where we (mis-) use the data cache to hold an
initial stack and some data.
XXX - this list needs to get updated!
- Watchdog:
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
support. There must support in the platform specific
code for a watchdog. For the 8xx and 8260 CPUs, the
SIU Watchdog feature is enabled in the SYPCR
register.
- U-Boot Version:
CONFIG_VERSION_VARIABLE
If this variable is defined, an environment variable
named "ver" is created by U-Boot showing the U-Boot
version as printed by the "version" command.
This variable is readonly.
- Real-Time Clock:
When CFG_CMD_DATE is selected, the type of the RTC
has to be selected, too. Define exactly one of the
following options:
CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
CONFIG_RTC_MC146818 - use MC146818 RTC
CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
CONFIG_RTC_DS164x - use Dallas DS164x RTC
Note that if the RTC uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
- Timestamp Support:
When CONFIG_TIMESTAMP is selected, the timestamp
(date and time) of an image is printed by image
commands like bootm or iminfo. This option is
automatically enabled when you select CFG_CMD_DATE .
- Partition Support:
CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
and/or CONFIG_ISO_PARTITION
If IDE or SCSI support is enabled (CFG_CMD_IDE or
CFG_CMD_SCSI) you must configure support for at least
one partition type as well.
- IDE Reset method:
CONFIG_IDE_RESET_ROUTINE
Set this to define that instead of a reset Pin, the
routine ide_set_reset(int idereset) will be used.
- ATAPI Support:
CONFIG_ATAPI
Set this to enable ATAPI support.
- SCSI Support:
At the moment only there is only support for the
SYM53C8XX SCSI controller; define
CONFIG_SCSI_SYM53C8XX to enable it.
CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
CFG_SCSI_MAX_LUN] can be adjusted to define the
maximum numbers of LUNs, SCSI ID's and target
devices.
CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
- NETWORK Support (PCI):
CONFIG_E1000
Support for Intel 8254x gigabit chips.
CONFIG_EEPRO100
Support for Intel 82557/82559/82559ER chips.
Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
write routine for first time initialisation.
CONFIG_TULIP
Support for Digital 2114x chips.
Optional CONFIG_TULIP_SELECT_MEDIA for board specific
modem chip initialisation (KS8761/QS6611).
CONFIG_NATSEMI
Support for National dp83815 chips.
CONFIG_NS8382X
Support for National dp8382[01] gigabit chips.
- NETWORK Support (other):
CONFIG_DRIVER_LAN91C96
Support for SMSC's LAN91C96 chips.
CONFIG_LAN91C96_BASE
Define this to hold the physical address
of the LAN91C96's I/O space
CONFIG_LAN91C96_USE_32_BIT
Define this to enable 32 bit addressing
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405); define
CONFIG_USB_UHCI to enable it.
define CONFIG_USB_KEYBOARD to enable the USB Keyboard
end define CONFIG_USB_STORAGE to enable the USB
storage devices.
Note:
Supported are USB Keyboards and USB Floppy drives
(TEAC FD-05PUB).
- MMC Support:
The MMC controller on the Intel PXA is supported. To
enable this define CONFIG_MMC. The MMC can be
accessed from the boot prompt by mapping the device
to physical memory similar to flash. Command line is
enabled with CFG_CMD_MMC. The MMC driver also works with
the FAT fs. This is enabled with CFG_CMD_FAT.
- Keyboard Support:
CONFIG_ISA_KEYBOARD
Define this to enable standard (PC-Style) keyboard
support
CONFIG_I8042_KBD
Standard PC keyboard driver with US (is default) and
GERMAN key layout (switch via environment 'keymap=de') support.
Export function i8042_kbd_init, i8042_tstc and i8042_getc
for cfb_console. Supports cursor blinking.
- Video support:
CONFIG_VIDEO
Define this to enable video support (for output to
video).
CONFIG_VIDEO_CT69000
Enable Chips & Technologies 69000 Video chip
CONFIG_VIDEO_SMI_LYNXEM
Enable Silicon Motion SMI 712/710/810 Video chip
Videomode are selected via environment 'videomode' with
standard LiLo mode numbers.
Following modes are supported (* is default):
800x600 1024x768 1280x1024
256 (8bit) 303* 305 307
65536 (16bit) 314 317 31a
16,7 Mill (24bit) 315 318 31b
(i.e. setenv videomode 317; saveenv; reset;)
CONFIG_VIDEO_SED13806
Enable Epson SED13806 driver. This driver supports 8bpp
and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
or CONFIG_VIDEO_SED13806_16BPP
- Keyboard Support:
CONFIG_KEYBOARD
Define this to enable a custom keyboard support.
This simply calls drv_keyboard_init() which must be
defined in your board-specific files.
The only board using this so far is RBC823.
- LCD Support: CONFIG_LCD
Define this to enable LCD support (for output to LCD
display); also select one of the supported displays
by defining one of these:
CONFIG_NEC_NL6648AC33:
NEC NL6648AC33-18. Active, color, single scan.
CONFIG_NEC_NL6648BC20
NEC NL6648BC20-08. 6.5", 640x480.
Active, color, single scan.
CONFIG_SHARP_16x9
Sharp 320x240. Active, color, single scan.
It isn't 16x9, and I am not sure what it is.
CONFIG_SHARP_LQ64D341
Sharp LQ64D341 display, 640x480.
Active, color, single scan.
CONFIG_HLD1045
HLD1045 display, 640x480.
Active, color, single scan.
CONFIG_OPTREX_BW
Optrex CBL50840-2 NF-FW 99 22 M5
or
Hitachi LMG6912RPFC-00T
or
Hitachi SP14Q002
320x240. Black & white.
Normally display is black on white background; define
CFG_WHITE_ON_BLACK to get it inverted.
- Spash Screen Support: CONFIG_SPLASH_SCREEN
If this option is set, the environment is checked for
a variable "splashimage". If found, the usual display
of logo, copyright and system information on the LCD
is supressed and the BMP image at the address
specified in "splashimage" is loaded instead. The
console is redirected to the "nulldev", too. This
allows for a "silent" boot where a splash screen is
loaded very quickly after power-on.
- Compression support:
CONFIG_BZIP2
If this option is set, support for bzip2 compressed
images is included. If not, only uncompressed and gzip
compressed images are supported.
NOTE: the bzip2 algorithm requires a lot of RAM, so
the malloc area (as defined by CFG_MALLOC_LEN) should
be at least 4MB.
- Ethernet address:
CONFIG_ETHADDR
CONFIG_ETH2ADDR
CONFIG_ETH3ADDR
Define a default value for ethernet address to use
for the respective ethernet interface, in case this
is not determined automatically.
- IP address:
CONFIG_IPADDR
Define a default value for the IP address to use for
the default ethernet interface, in case this is not
determined through e.g. bootp.
- Server IP address:
CONFIG_SERVERIP
Defines a default value for theIP address of a TFTP
server to contact when using the "tftboot" command.
- BOOTP Recovery Mode:
CONFIG_BOOTP_RANDOM_DELAY
If you have many targets in a network that try to
boot using BOOTP, you may want to avoid that all
systems send out BOOTP requests at precisely the same
moment (which would happen for instance at recovery
from a power failure, when all systems will try to
boot, thus flooding the BOOTP server. Defining
CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
inserted before sending out BOOTP requests. The
following delays are insterted then:
1st BOOTP request: delay 0 ... 1 sec
2nd BOOTP request: delay 0 ... 2 sec
3rd BOOTP request: delay 0 ... 4 sec
4th and following
BOOTP requests: delay 0 ... 8 sec
- DHCP Advanced Options:
CONFIG_BOOTP_MASK
You can fine tune the DHCP functionality by adding
these flags to the CONFIG_BOOTP_MASK define:
CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
serverip from a DHCP server, it is possible that more
than one DNS serverip is offered to the client.
If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
serverip will be stored in the additional environment
variable "dnsip2". The first DNS serverip is always
stored in the variable "dnsip", when CONFIG_BOOTP_DNS
is added to the CONFIG_BOOTP_MASK.
CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
to do a dynamic update of a DNS server. To do this, they
need the hostname of the DHCP requester.
If CONFIG_BOOP_SEND_HOSTNAME is added to the
CONFIG_BOOTP_MASK, the content of the "hostname"
environment variable is passed as option 12 to
the DHCP server.
- Status LED: CONFIG_STATUS_LED
Several configurations allow to display the current
status using a LED. For instance, the LED will blink
fast while running U-Boot code, stop blinking as
soon as a reply to a BOOTP request was received, and
start blinking slow once the Linux kernel is running
(supported by a status LED driver in the Linux
kernel). Defining CONFIG_STATUS_LED enables this
feature in U-Boot.
- CAN Support: CONFIG_CAN_DRIVER
Defining CONFIG_CAN_DRIVER enables CAN driver support
on those systems that support this (optional)
feature, like the TQM8xxL modules.
- I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
These enable I2C serial bus commands. Defining either of
(but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
include the appropriate I2C driver for the selected cpu.
This will allow you to use i2c commands at the u-boot
command line (as long as you set CFG_CMD_I2C in
CONFIG_COMMANDS) and communicate with i2c based realtime
clock chips. See common/cmd_i2c.c for a description of the
command line interface.
CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
CONFIG_SOFT_I2C configures u-boot to use a software (aka
bit-banging) driver instead of CPM or similar hardware
support for I2C.
There are several other quantities that must also be
defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
In both cases you will need to define CFG_I2C_SPEED
to be the frequency (in Hz) at which you wish your i2c bus
to run and CFG_I2C_SLAVE to be the address of this node (ie
the cpu's i2c node address).
Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
sets the cpu up as a master node and so its address should
therefore be cleared to 0 (See, eg, MPC823e User's Manual
p.16-473). So, set CFG_I2C_SLAVE to 0.
That's all that's required for CONFIG_HARD_I2C.
If you use the software i2c interface (CONFIG_SOFT_I2C)
then the following macros need to be defined (examples are
from include/configs/lwmon.h):
I2C_INIT
(Optional). Any commands necessary to enable the I2C
controller or configure ports.
eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
I2C_PORT
(Only for MPC8260 CPU). The I/O port to use (the code