forked from triffid/FiveD_on_Arduino
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Makefile
170 lines (140 loc) · 9.25 KB
/
Makefile
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
##############################################################################
# #
# FiveD on Arduino - alternative firmware for repraps #
# #
# by Triffid Hunter, Traumflug, jakepoz #
# #
# #
# This firmware is Copyright (C) 2009-2010 Michael Moon aka Triffid_Hunter #
# #
# This program is free software; you can redistribute it and/or modify #
# it under the terms of the GNU General Public License as published by #
# the Free Software Foundation; either version 2 of the License, or #
# (at your option) any later version. #
# #
# This program is distributed in the hope that it will be useful, #
# but WITHOUT ANY WARRANTY; without even the implied warranty of #
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the #
# GNU General Public License for more details. #
# #
# You should have received a copy of the GNU General Public License #
# along with this program; if not, write to the Free Software #
# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA #
# #
##############################################################################
##############################################################################
# #
# Change these to suit your hardware #
# #
##############################################################################
# MCU_TARGET = atmega168
# MCU_TARGET = atmega328p
MCU_TARGET = atmega644p
# MCU_TARGET = atmega1280
# F_CPU = 16000000L
##############################################################################
# #
# Available Defines: #
# #
# DEBUG #
# enables tons of debugging output. may cause host-side talkers to choke #
# XONXOFF #
# enables XON/XOFF flow control for stupid or crude talkers #
# ACCELERATION_REPRAP #
# enables reprap-style acceleration #
# ACCELERATION_RAMPING #
# enables start/stop ramping #
# ACCELERATION_TEMPORAL #
# enables experimental temporal step algorithm - not technically a type of #
# acceleration, but since it controls step timing it seems appropriate #
# GEN3 #
# build for standard reprap electronics instead of your custom rig #
# HOST #
# this is the motherboard for GEN3- don't touch! Extruder has its own #
# Makefile. #
# #
##############################################################################
# DEFS = -DF_CPU=$(F_CPU) -DHOST -DGEN3
# DEFS += "-DDEBUG=1"
##############################################################################
# #
# Programmer settings for "make program" #
# #
##############################################################################
AVRDUDE = avrdude
AVRDUDECONF = /etc/avrdude.conf
##############################################################################
# #
# udev rule for /dev/arduino (insert into /etc/udev/rules.d/99-local.rules) #
# SUBSYSTEMS=="usb", ATTRS{idProduct}=="6001", ATTRS{idVendor}=="0403", #
# NAME="%k", SYMLINK+="arduino", SYMLINK+="arduino_$attr{serial}", #
# MODE="0660" #
# #
##############################################################################
PROGPORT = /dev/arduino
# atmega168
#PROGBAUD = 19200
# atmega328p, 644p, 1280
PROGBAUD = 57600
##############################################################################
# #
# These defaults should be ok, change if you need to #
# #
##############################################################################
PROGRAM = mendel
SOURCES = $(PROGRAM).c serial.c dda.c gcode_parse.c gcode_process.c timer.c temp.c sermsg.c dda_queue.c watchdog.c debug.c sersendf.c heater.c analog.c delay.c intercom.c pinio.c clock.c
ARCH = avr-
CC = $(ARCH)gcc
OBJDUMP = $(ARCH)objdump
OBJCOPY = $(ARCH)objcopy
OPTIMIZE = -Os -ffunction-sections -finline-functions-called-once -mcall-prologues
# OPTIMIZE = -O0
CFLAGS = -g -Wall -Wstrict-prototypes $(OPTIMIZE) -mmcu=$(MCU_TARGET) $(DEFS) -std=gnu99 -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -save-temps
LDFLAGS = -Wl,--as-needed -Wl,--gc-sections
OBJ = $(patsubst %.c,%.o,${SOURCES})
.PHONY: all program clean size
.PRECIOUS: %.o %.elf
all: config.h $(PROGRAM).hex $(PROGRAM).lst $(PROGRAM).sym size
program: $(PROGRAM).hex config.h
stty $(PROGBAUD) raw ignbrk hup < $(PROGPORT)
@sleep 0.1
@stty $(PROGBAUD) raw ignbrk hup < $(PROGPORT)
$(AVRDUDE) -cstk500v1 -b$(PROGBAUD) -p$(MCU_TARGET) -P$(PROGPORT) -C$(AVRDUDECONF) -U flash:w:$^
stty 115200 raw ignbrk -hup -echo ixoff < $(PROGPORT)
program-fuses:
avr-objdump -s -j .fuse mendel.o | perl -ne '/\s0000\s([0-9a-f]{2})/ && print "$$1\n"' > lfuse
avr-objdump -s -j .fuse mendel.o | perl -ne '/\s0000\s..([0-9a-f]{2})/ && print "$$1\n"' > hfuse
avr-objdump -s -j .fuse mendel.o | perl -ne '/\s0000\s....([0-9a-f]{2})/ && print "$$1\n"' > efuse
$(AVRDUDE) -cstk500v1 -b$(PROGBAUD) -p$(MCU_TARGET) -P$(PROGPORT) -C$(AVRDUDECONF) -U lfuse:w:lfuse
$(AVRDUDE) -cstk500v1 -b$(PROGBAUD) -p$(MCU_TARGET) -P$(PROGPORT) -C$(AVRDUDECONF) -U hfuse:w:hfuse
$(AVRDUDE) -cstk500v1 -b$(PROGBAUD) -p$(MCU_TARGET) -P$(PROGPORT) -C$(AVRDUDECONF) -U efuse:w:efuse
clean:
rm -rf *.o *.elf *.lst *.map *.sym *.lss *.eep *.srec *.bin *.hex *.al *.i *.s *~ *fuse
size: $(PROGRAM).elf
@echo " SIZE Atmega168 Atmega328p Atmega644"
@$(OBJDUMP) -h $^ | perl -MPOSIX -ne '/.(text)\s+([0-9a-f]+)/ && do { $$a += eval "0x$$2" }; END { printf " FLASH : %5d bytes (%2d%% of %2dkb) (%2d%% of %2dkb) (%2d%% of %2dkb)\n", $$a, ceil($$a * 100 / (15 * 1024)), 15, ceil($$a * 100 / (31 * 1024)), 31, ceil($$a * 100 / (63 * 1024)), 63 }'
@$(OBJDUMP) -h $^ | perl -MPOSIX -ne '/.(data|bss)\s+([0-9a-f]+)/ && do { $$a += eval "0x$$2" }; END { printf " RAM : %5d bytes (%2d%% of %2dkb) (%2d%% of %2dkb) (%2d%% of %2dkb)\n", $$a, ceil($$a * 100 / (1 * 1024)), 1, ceil($$a * 100 / (2 * 1024)), 2, ceil($$a * 100 / (4 * 1024)), 4 }'
@$(OBJDUMP) -h $^ | perl -MPOSIX -ne '/.(eeprom)\s+([0-9a-f]+)/ && do { $$a += eval "0x$$2" }; END { printf " EEPROM: %5d bytes (%2d%% of %2dkb) (%2d%% of %2dkb) (%2d%% of %2dkb)\n", $$a, ceil($$a * 100 / (1 * 1024)), 1, ceil($$a * 100 / (2 * 1024)), 2, ceil($$a * 100 / (2 * 1024)), 2 }'
config.h: config.h.dist
@echo "Please review config.h, as config.h.dist is more recent."
@echo
@diff -bBEuF '^. [[:digit:]]. [[:upper:]]' config.h config.h.dist
@false
%.o: %.c config.h Makefile
@echo " CC $@"
@$(CC) -c $(CFLAGS) -Wa,-adhlns=$(<:.c=.al) -o $@ $(subst .o,.c,$@)
%.elf: $(OBJ)
@echo " LINK $@"
@$(CC) $(CFLAGS) $(LDFLAGS) -o $@ $^ $(LIBS)
%.lst: %.elf
@echo " OBJDUMP $@"
@$(OBJDUMP) -h -S $< > $@
%.hex: %.elf
@echo " OBJCOPY $@"
@$(OBJCOPY) -j .text -j .data -O ihex -R .eeprom -R .fuse -R .lock $< $@
%.bin: %.elf
@echo " OBJCOPY $@"
@$(OBJCOPY) -j .text -j .data -O binary $< $@
%.sym: %.elf
@echo " SYM $@"
@$(OBJDUMP) -t $< | perl -ne 'BEGIN { printf " ADDR NAME SIZE\n"; } /([0-9a-f]+)\s+(\w+)\s+O\s+\.(bss|data)\s+([0-9a-f]+)\s+(\w+)/ && printf "0x%04x %-20s +%d\n", eval("0x$$1") & 0xFFFF, $$5, eval("0x$$4")' | sort -k1 > $@