Some parts are listed with a zero quantity. This are meant to be alternates (and should be marked with ALT). Choose what works best for you.
PJ302M jacks are available from Thonk, Synthcube and Modular Addict among other sources. Or you can get the alternate CUI MJ-3536 jack listed below from Mouser.
Raspberry Pi 3B+ or 4B can be purchased from a number of sources such as PiShop.us, Adafruit, CanaKit, Element14, etc. Mouser also now carries Pis (although a bit more expensive) if you want one-stop shopping (part numbers listed below).
ENC4 is optional and is not functional for norns right now. If you want to use Orac later, get 4 encoders.
Note - some Mouser part numbers may be out of stock (usually passives), so you may need to search for equivalent alternatives
| Mouser | QTY | Part | Value | Package |
|---|---|---|---|---|
| 603-AC0805FR-07100RL | 2 | R4 R5 | 100R | 0805 |
| 603-RC0805FR-07220RL | 4 | R16 R17 R18 R19 | 220R | 0805 |
| 660-RK73H2ATTD2201F | 2 | R14 R15 | 2.2K | 0805 |
| 603-RC0805FR-075K1L | 2 | R20 R21 | 5.1K | 0805 |
| 279-CRGCQ0805F5K6 | 4 | R10 R11 R12 R13 | 5.6K | 0805 |
| 603-RC0805FR-0710KL | 3 | R1 R2 R3 | 10k | 0805 |
| RC0805FR-0747KL | 4 | R6 R7 R8 R9 | 47K | 0805 |
| 603-CC805JRNPO9BN180 | 2 | C10 C11 | 18p | 0805 |
| 710-885012207082 | 2 | C8 C9 | 220p | 0805 |
| 80-C0805C104J5RACLR | 7 | C1 C2 C3 C4 C5 C6 C7 | 100n | 0805 |
| 710-860020672005 | 4 | C12 C13 C14 C15 | 1uF Electrolytic | 11mm |
| 667-ECE-A1VKS100 | 3 | C18 C19 C20 | 10uF Electrolytic | 11mm |
| 80-ESH227M016AE3AA | 2 | C16 C17 | 220uF Electrolytic | 11mm |
| ADP150AUJZ-3.3-R7 | 1 | ADP150-3.3 | ADP150AUJZ-3.3-R7 | |
| 238-WM8731SEDS/RV | 1 | U1 | WM8731SEDS/V | SSOP28 |
| 815-ABLS2-12.2-D4Y-T | 1 | Y1 | 12.288MHz | HC49UP |
| 652-PEC11R-4015F-N24 | 3 | ENC1 ENC2 ENC3 (ENC4) | 15mm Flatted shaft | |
| 652-PEC11R-4015K-N24 | 0 | ALT ENC1 ENC2 ENC3 (ENC4) | 15mm Knurled shaft | |
| 652-PEC11R-4020F-N24 | 0 | ALT ENC1 ENC2 ENC3 (ENC4) | 20mm Flatted shaft | |
| NHD-2.7-12864WDW3 | 1 | SSD1322 | NHD-2.7-12864WDW3 OLED Display | |
| 490-SJ1-3523N | 1 | CUI_SJ1-3523N | STEREOJACK Headphone | |
| 4 | Z5 Z6 Z7 Z8 | PJ302M2 1/8in mono jack | PJ302M | |
| 490-MJ-3536 | 0 | ALT | alternate 1/8in jack - CUI MJ-3536 | |
| 517-929984-01-20-RK | 1 | 1x20 low profile female header for disp | ||
| 200-SLW12001TS | 0 | ALT | 1x20 low profile female header for disp | |
| 855-M20-9992045 | 1 | 1x20 male pin header for disp (gold) | ||
| 855-M20-9992046 | 0 | ALT | 1x40 male pin header for disp (tin) | |
| 485-2222 | 1 | 2x20 GPIO female header for RasPi | Adafruit Part # 2222 | |
| 855-M20-7832046 | 0 | ALT | Alternate 2x20 GPIO female header | |
| 649-10027011-106HLF | 1 | UART 6 pin header | ||
| 806-KUSBX-SLCS1N14-B | 1 | USB C jack | ** See note | |
| 5GTH920 | 3 | S1 S2 S3 | 5G MEC switch - Clicky | |
| 5GTH920Q | 0 | S1 S2 S3 ALT | 5G MEC switch - Quiet | |
| 642-1US09 | 3 | 5G MEC switch caps black | ||
| 642-1US03 | 0 | ALT | 5G MEC switch caps gray | |
| 642-1DS09 | 0 | ALT | 5G MEC switch caps black - rounded | |
| RPI3-MODBP-BULK | 1 | RPI3 b+ | ||
| RPI4-MODBP-2GB-BULK | 0 | RPI4 b 2GB | ||
| RPI4-MODBP-4GB-BULK | 0 | RPI4 b 4GB | ||
| 1 | RPI Power supply - 3A USB-C recommended |
If out of stock at Mouser/Digikey, the OLED display can also be purchased directly from the manufacturer here.
You might need to adjust order quantities, get knurled encoders, or get clicky buttons instead of quiet. So be sure to check part numbers and availability before ordering. NOTE - some parts may be out of stock. See the alternates listed above for other choices.
** The USB-C jack can be considered optional. You can power everything directly from the Raspberry Pi's own power input OR the Fates USB-C jack (DO NOT TRY TO POWER BOTH!)
A mouser cart is setup with these parts (not including Pi). Audio jacks are NOT INCLUDED in this cart (see note above). If you want them from Mouser order 4 of 490-MJ-3536
NOTE - Mouser cart likely has items out of stock right now. Check above for alternate part numbers.
NOTE - If you're getting an acrylic case from the Denki-oto shop, the case kit includes spacers/screws.
Spacers/screws are also not included in the cart above. There is a separate cart for spacers if you need them (Cart does not include screws).
Spacers/screws - I use 2.5mm size screws and spacers. 3mm should work as well.
Here's my spacer list. This may also be to taste if you solder the display header closer to the main board. Sorry I don't have a good Mouser part number for 2.5M screws.
| qty | height | location | ||
|---|---|---|---|---|
| 855-R25-3000302 | 2 | 3mm | M-F | Right side pi bottom |
| 761-M2101-2545-AL | 2 | 6mm | M-F | under oled display corners |
| 761-M1258-2545-AL | 2 | 11mm | F-F | Right side pi |
| 761-M1262-2545-AL | 4 | 15mm | F-F | left/back side |
| 761-M2105-2545-AL | 4 | 10mm | M-F | top corners |
| 2 | 5mm long | 2.5mm rack screws | ||
| 10 | 6mm long | 2.5mm rack screws | ||
| 1 | 8-10mm long | 2.5mm rack screws |
https://modularaddict.com/parts/knobs/reanp670d-knobs
https://store.djtechtools.com/products/chroma-caps-knobs-and-faders
https://synthcube.com/cart/synth-diy/parts/knobs/rogan-series-p-knobs
https://modularaddict.com/parts/knobs/pt2d-knob
https://modularaddict.com/parts/knobs/albs-midibox-knobs