PRTouch_v2 Configuration Documentation?

[sleewok]

Is there any documentation available for the Klipper config parameters of the PRTouch_v2? I would like to make some tweaks but I am unable to find any information on what the various parameters actually do.

[lancer234]

Is there any documentation available for the Klipper config parameters of the PRTouch_v2? I would like to make some tweaks but I am unable to find any information on what the various parameters actually do.

Did you have any luck with this?

[sleewok]

Nope. I ended up disabling the prtouch and installed my old CR-Touch on my K1C. It is faster and more accurate by far. Shaves over 5 minutes off the print start too.

…

On Fri, May 31, 2024, 1:41 PM lancer234 ***@***.***> wrote: Is there any documentation available for the Klipper config parameters of the PRTouch_v2? I would like to make some tweaks but I am unable to find any information on what the various parameters actually do. Did you have any luck with this? — Reply to this email directly, view it on GitHub <#104 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AACKOLGQSU3ISKIRD3WDBSDZFCY6HAVCNFSM6AAAAABFLMH3D6VHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TMMRRG4ZDO> . You are receiving this because you authored the thread.Message ID: <CrealityOfficial/Creality_Sonic_Pad/repo-discussions/104/comments/9621727 @github.com>

[FxWoody]

i have a KE and need to disable the PrTouch and Bltouch too ... what did you do exactly ??? Just # every lines in printer.cfg ??? Because i still end up with errors in Mainsail :( Want to install Beacon instead ;)

[sleewok]

I think there are some related python files that need modified or removed. I don't recall which ones.

…

On Sat, Aug 31, 2024, 2:42 PM FxWoody ***@***.***> wrote: i have a KE and need to disable the PrTouch and Bltouch too ... what did you do exactly ??? Just # every lines in printer.cfg ??? Because i still end up with errors in Mainsail :( Want to install Beacon instead ;) — Reply to this email directly, view it on GitHub <#104 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AACKOLGHHBO5QREVSQLCI2TZUIFBXAVCNFSM6AAAAABFLMH3D6VHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTANJQHA2DANY> . You are receiving this because you authored the thread.Message ID: <CrealityOfficial/Creality_Sonic_Pad/repo-discussions/104/comments/10508407 @github.com>

[Chris77123]

Is there any documentation available for the Klipper config parameters of the PRTouch_v2? I would like to make some tweaks but I am unable to find any information on what the various parameters actually do.

?

[sleewok]

I still haven't found anything. It's a shame that Creality has not released the source code for it (AFAIK). There's a way to wire the load cells in parallel (so that the controller sees them as one loadcell) and have klipper handle the loadcell. At least for the K1/K1C (https://github.com/cryoz/K1_tenso_manual/blob/main/README_ENG.md).

I haven't tried it yet. The required klipper branch is a bit behind mainline and I need the version that supports Orca Slicer's Adaptive Pressure Advance.