| User | Password | Internal MD5 Hash | CGI | |
|---|---|---|---|---|
| admin | admin | f6fdffe48c908deb0f4c3bd36c032e72 |
login.cgi | ✔ |
| hengrui | ❓ | 81d57ea79621e8887914f40ee4122185 |
login_ft.cgi | ❌ |
Factory CGI can be accessed directly via the admin credentials
| CGI | Description |
|---|---|
| menu_ft.cgi | Factory Menu |
| ftdft.cgi | Factory Defaults |
| ftlogo.cgi | Factory Logo |
| ftcolor.cgi | Factory Colours |
Warning
The orientation is different for both boards
| Pin | SWTG115AS | SWTG118AS | Notes |
|---|---|---|---|
| 1 | TX | TX | Square Pad |
| 2 | GND | GND | |
| 3 | RX | RX | |
| 4 | VCC | VCC |
| Unmanaged | Web Managed | |
|---|---|---|
| Speed | 9600 | 57600 |
| Parity | None | None |
| Data-bits | 8 | 8 |
| Stop-bits | 1 | 1 |
==========Loader start===========
Press any key to start the normal procedure.
To run SPI flash viewer, press [v]
To enforce the download of the runtime kernel, press [ESC] .....
cmd -1
Check Runtime Image.....
Chksum Correct!
RunTime Kernel Starting....
Ver8373_72: C
Not rtl8221b and skip init flow...id = c849
###SDS FW Load finished !!
===========================Config Area pre-check Starts.=====================.
Pre-Check the config size structure is equal or not.
(sizeof(configCache)) a36.
(FLSH_ADDR_END-FLSH_CONFIG_ADDR_START) a36.
(FLSH_CONFIG_ADDR_START) 1fe000.
(FLSH_ADDR_END) 1fea36.
It seems no risk!..................
==============================Config Area pre-check ends.===================.
SalFlshCopyFlshToCache()
sal_sys_config_restore()
Restore dhcp state is: 0
Restore ip is: 192.168.2.1
...OK
sal_mirror_config_restore()...OK
sal_qos_config_restore()...OK
sal_vlan_config_restore()...OK
sal_rate_config_restore()...OK
sal_trunk_config_restore()...OK
sal_l2_config_restore()...OK
sal_loop_config_restore()...OK
sal_eee_config_restore()...OK
sal_stp_config_restore()...OK
sal_igmp_config_restore()...OK
sal_port_config_restore()...OK
#############According to the flash setting to set the WEB/DUMB mode
#############Read the web/dumb mode.....!!!###
#############web_dumb_cfg.vld_flag=-1, web_dumb_cfg.mode=-1
#############Begin to set the web mode
################################################################
############Login Menu ############
### Please input uboot password below: ###
The "uboot" password is Switch321
Login OK.
RTL8372:
| Command | Description | Notes |
|---|---|---|
dft |
Resets the default factory configuration | 0x005DB50 and colours at 0x000DE520 |
fiber |
Displays SFP+ port status | |
gpio |
Displays GPIO 54 status | |
poe |
Displays PoE status | |
regset <reg> <value> |
Sets a register to a specified value | |
regget <reg> |
Display the specified registers value | |
reboot |
Reboots the switch | |
reset |
Resets the user configuration | |
showip |
Displays the system information | |
stp |
Displays the Spanning Tree details | |
web |
Sets the web mode | Sets web config offsets 0x001FC026 and 0x001FC027 to 1 |
If the runtime fails, the loader will fallback to the firmware upload sequence at http://192.168.1.1. It may also be triggered over serial by holding ESC on power on.
==========Loader start===========
Press any key to start the normal procedure.
To run SPI flash viewer, press [v]
To enforce the download of the runtime kernel, press [ESC] .
cmd 27
sal_sys_runtime_crc_set
loader start
load MAC from nvcfg
IP:192.168.1.1
Mask:255.255.255.0
GW:192.168.1.254
MAC:AA.BB.CC.DD.EE.FF=========================SPI FLASH VIEWER=============================
b: reboot
e <addr>: Erase flash with the address of <addr>
ev <addr>: Erase flash with the address of <addr> and then Verify
r <addr> <len>: read flash from the address of <addr> and then dump
c: check runtime kernel without boot
cb: check runtime kernel and boot if checksum is pass
h: print header
l: load runtime kernel
v: show verobose information
m: print this menu
q: quit from spi flash view
>There 2 protected region(s).
Portected region 0: 0x000000-0x001000
Portected region 1: 0x004000-0x01c000| Firmware Offset | Length | Description | Notes |
|---|---|---|---|
0x001FC000 |
0x00000006 |
MAC address | |
0x001FC026 |
0x00000002 |
Web/Dumb mode | 0x00 = Dumb Mode, 0x01 = Web Mode, 0xFF = Auto detect |
0x001FD000 |
0x0000023D |
Factory settings | |
0x001FE000 |
0x00000A42 |
User settings |
| Firmware Offset | Length | Update Offset | Length |
|---|---|---|---|
0x00001000 |
0x00002ffe |
0x00000014 |
0x00002ffe |
0x0001C000 |
0x00001000 |
0x00003012 |
0x00001000 |
0x0001D000 |
0x001DF000 |
0x00003ffe |
eof |
error SDS_MODE
LINE 2178
RTL8371B start aas
RTL8371B:RTL8371B:?
rst: -reset chip
the following is set IOL test mode
f: -fix pattern: please input port: 0-7;
r: -random pattern: please input port: 0-7;
10: -10M MDI: please input port: 0-7;
11: -10M MDIx: please input port: 0-7;
100: -100M MDI: please input port: 0-7;
101: -100M MDIX: please input port: 0-7;
g1: -giga mode1: please input port: 0-7;
g2: -giga mode2: please input port: 0-7;
g3: -giga mode3: please input port: 0-7;
g4: -giga mode4: please input port: 0-7;
1: -2.5G mode1: please input port: 0-7;
2: -2.5G mode2: please input port: 0-7;
3: -2.5G mode3: please input port(0~7) and lp;
4: -2.5G mode4: please input tone(1~5) and port(0~7);
5: -2.5G mode5: please input port: 0-7;
6: -2.5G mode6: please input port: 0-7;
the following is set sds test mode,chip sel:8373/8372: 3, 8224: 4;
sd: -please input chip: 3 or 4; prbs31:31; sds: 0~1; on/off:1 or 0;
sd: -please input chip: 3 or 4; prbs9:9; sds: 0~1; on/off:1 or 0;
sd: -please input chip: 3 or 4; tx_8081: 8; sds: 0~1; onoff:1 or 0;
pre: -please input chip: 3 or 4; sds: 0~1; pre: 0~63, endis:0~1;
main: -please input chip: 3 or 4; sds: 0~1; mamp: 0~63, boost:0~1, endis: 0~1;
post: -please input chip: 3 or 4; sds: 0~1; post: 0~63, endis: 0~1;
tx: -please input chip: 3 or 4; sds: 0~1; z0:0~15;
eye: -please input chip: 3 or 4; sds: 0~1; phyad: 0; frame:0~x;
dump: -dump amp cfg;please input chip: 3 or 4; sds:0~1;usage: calcsum.py [-h] [-u] firmware
SWTG Update Firmware Checksum Calculator
positional arguments:
firmware
options:
-h, --help show this help message and exit
-u, --update Re-calculate sums