jtag: bcm2835gpio: fix macro definition

The macros trigger few errors with checkpatch:

	ERROR:MACRO_ARG_REUSE: Macro argument reuse 'g' - possible
	side-effects?

	ERROR:TRAILING_STATEMENTS: trailing statements should be
	on next line

	ERROR:SPACING: spaces preferred around (several cases)

	ERROR:SINGLE_STATEMENT_DO_WHILE_MACRO: Single statement
	macros should not use a do {} while (0) loop

plus an empty line triggers

	ERROR:BRACES: Blank lines aren't necessary before a close
	brace '}'

Fix them!

Change-Id: I0690b68b511ed7f45a7e0909a0addd2822ba9fe8
Signed-off-by: Antonio Borneo <[email protected]>
Reviewed-on: https://review.openocd.org/c/openocd/+/8499
Tested-by: jenkins
Reviewed-by: Tomas Vanek <[email protected]>

src/jtag/drivers/bcm2835gpio.c

@@ -31,16 +31,28 @@ static off_t bcm2835_peri_base = 0x20000000;
 #define BCM2835_GPIO_MODE_OUTPUT 1
 
 /* GPIO setup macros */
-#define MODE_GPIO(g) (*(pio_base+((g)/10))>>(((g)%10)*3) & 7)
-#define INP_GPIO(g) do { *(pio_base+((g)/10)) &= ~(7<<(((g)%10)*3)); } while (0)
-#define SET_MODE_GPIO(g, m) do { /* clear the mode bits first, then set as necessary */ \
- INP_GPIO(g); \
- *(pio_base+((g)/10)) |= ((m)<<(((g)%10)*3)); } while (0)
+#define MODE_GPIO(_g) ({ \
+ typeof(_g) g = (_g); \
+ *(pio_base + (g / 10)) >> ((g % 10) * 3) & 7; \
+})
+
+#define INP_GPIO(_g) do { \
+ typeof(_g) g1 = (_g); \
+ *(pio_base + (g1 / 10)) &= ~(7 << ((g1 % 10) * 3)); \
+} while (0)
+
+#define SET_MODE_GPIO(_g, m) do { \
+ typeof(_g) g = (_g); \
+ /* clear the mode bits first, then set as necessary */ \
+ INP_GPIO(g); \
+ *(pio_base + (g / 10)) |= ((m) << ((g % 10) * 3)); \
+} while (0)
+
 #define OUT_GPIO(g) SET_MODE_GPIO(g, BCM2835_GPIO_MODE_OUTPUT)
 
-#define GPIO_SET (*(pio_base+7)) /* sets bits which are 1, ignores bits which are 0 */
-#define GPIO_CLR (*(pio_base+10)) /* clears bits which are 1, ignores bits which are 0 */
-#define GPIO_LEV (*(pio_base+13)) /* current level of the pin */
+#define GPIO_SET (*(pio_base + 7)) /* sets bits which are 1, ignores bits which are 0 */
+#define GPIO_CLR (*(pio_base + 10)) /* clears bits which are 1, ignores bits which are 0 */
+#define GPIO_LEV (*(pio_base + 13)) /* current level of the pin */
 
 static int dev_mem_fd;
 static volatile uint32_t *pio_base = MAP_FAILED;
@@ -175,7 +187,6 @@ static bb_value_t bcm2835gpio_read(void)
  unsigned int shift = adapter_gpio_config[ADAPTER_GPIO_IDX_TDO].gpio_num;
  uint32_t value = (GPIO_LEV >> shift) & 1;
  return value ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_TDO].active_low ? BB_HIGH : BB_LOW);
-
 }
 
 static int bcm2835gpio_write(int tck, int tms, int tdi)